[open] error when trying to open the experiment file

Comments

• ronishafir1

  December 2013 edited 9:30AM

  This is the message: "See the logfile 'C:/Prtogram Files (x86)/OpenSesame/opensesame.exe.log' for details".
• sebastiaan

  January 2014 edited 9:30AM

  Hi Roni,

  Could you please post the contents of opensesame.exe.log? That file will contain the actual error message.

  Cheers,
  Sebastiaan

  
  
  Check out SigmundAI.eu for our OpenSesame AI assistant!
  
• ronishafir1

  January 2014 edited January 2014

  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  Traceback (most recent call last):
    File "opensesame", line 108, in <module>
    File "dist\libqtopensesame\qtopensesame.py", line 868, in open_file
  UnicodeDecodeError: 'ascii' codec can't decode byte 0xe0 in position 22: ordinal not in range(128)
  
• ronishafir1

  January 2014 edited 9:30AM

  Thanks!
• sebastiaan

  January 2014 edited 9:30AM

  Hi Roni,

  This seems to be an error that results from non-Latin characters in your filename. However, this problem should be resolved (at least) as of version 0.27.4. Are you using an older version of OpenSesame? If yes, then updating should resolve the issue. If no, could you try if the latest pre-release of 2.8.0 resolves the issue?

  • http://forum.cogsci.nl/index.php?p=/discussion/688/test-drive-opensesame-2-8-0

  Cheers!
  Sebastiaan

  
  
  Check out SigmundAI.eu for our OpenSesame AI assistant!
  
• Marie

  January 2014 edited 9:30AM

  Hi Roni,

  I had the same problem.
  I'm french. So, sometime I use accents for my fils (bad idea I know).

  I saw that I had accents in the link where is my experiment. After deleting it, my problem is resolved.

  I hope that it will help you.

  Marie