[open] EEG parallel port trigger for MAC

Comments

• Edwin

  May 2014 edited 7:56AM

  Hi Mona,

  Actually, the parallel port plug-in works on Linux as well, using the parallel module (or an onboard modified version). This might just work on OS X, as the architecture is pretty similar. I don't have any experience on this, though (frankly, I didn't even know there are still Macs out there with a parallel port!).

  Good luck!

  Edwin
• Mona

  May 2014 edited 7:56AM

  Dear Edwin,

  thank you for your reply. I see, for E-prime we created a new port specifically for Eprime in the network section of the Mac, but we used the Mac IP address for the configuration with Eprime on the PC. The opensesame parallel module is asking for a port (and obviously gives an error if I fill in the IP address of the Mac). How shall I best establish the connection?

  Our system (Mac EEG recording unit and windows pc on which the behavioral tasks are done) is sufficiently set up and connected, and I am familiar with setting up the configurations between both computers for Eprime, but I would like to introduce opensesame to our lab and for that I need to enable simultaneous EEG recording.

  As I see it, I need to add a port in the Mac to allow connection with opensesame (you have a default port name?) and need to allow opensesame to connect with the Mac with a similar module as the parallel except that it allows an IP input.

  Maybe this has been tried out before?

  thank you, Mona
• Edwin

  May 2014 edited 7:56AM

  Hi Mona,

  Some bad news, I'm afraid: I don't think anyone has used such a setup before, and I don't see a readymade solution.

  It sounds like it's configured via ethernet rather than via the parallel port. In any way, it's not going to be possible to establish a connection using the existing plug-ins. I would suggest either sticking with your current solution (without OpenSesame), running a virtual machine or native Windows installation (if you can configure your EEG equipment to work via Windows), or to use Python's socket module in an inline_script (see here for an example).

  If you manage to work something out, please do report back on the forum. Other might benefit

  Good luck!
• sebastiaan

  May 2014 edited 7:56AM

  Hi Mona,

  Edwin's right. What you're dealing with is not a parallel port, but an ethernet connection, and more specifically a UDP (datagram) connection. (Or at least I suspect that's what it is, there's a slight chance that it's TCP/IP.) It's not that hard to get this working though.

  Basically, you can create a socket at the start of your experiment with the script below. You need to specify the IP address of the Mac recorder computer. And in the Mac you need to indicate which you port you used (or change the port in the script to match the one specified in the Mac recorder computer).

  import socket
  # The IP address of the recorder PC
  ip = '127.0.0.1'
  # The communication port, which can probably be anything as long as it's
  # the same in OpenSesame and the recorder PC
  port = 40008
  # Initialize a socket object
  print('Opening socket')
  my_socket = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
  print('Socket opened on ip %s and port %d' % (ip, port))
  

  Once you've done this, you can send a trigger (I'm assuming a 0-255 byte trigger here, because that's what's usually done in EEG) with the following script:

  trigger_value = 255
  print('Sending trigger %d' % trigger_value)
  my_socket.sendto(chr(trigger_value), (ip, port))
  print('Trigger sent!')
  

  Something like this should do the trick. UDP communication is really not that hard, and you can read more about it here:

  • https://docs.python.org/2/library/socket.html

  Cheers!
  Sebastiaan

  
  
  Check out SigmundAI.eu for our OpenSesame AI assistant!
  
• Mona

  May 2014 edited 7:56AM

  YES! thank you! that was the right direction! We managed to also get a 'start & stop EEG recording' impulse and triggers.

  As soon as it is a bit polished I will post it here in case anyone is in a similar position.

  Soon our whole lab will be geared up for open sesame! Thank you for this amazing program and your nice & fast responses!

  Mona
• sebastiaan

  May 2014 edited 7:56AM

  Soon our whole lab will be geared up for open sesame!

  Good to hear!

  
  
  Check out SigmundAI.eu for our OpenSesame AI assistant!
  
• Mona

  June 2014 edited 7:56AM

  I actually found a whole website dedicated to EGI-netstation communication for future users:

  https://code.google.com/p/pynetstation/

  Enjoy!