USB self made button box

Comments

• labovich

  August 2016 edited August 2016

  more specifically, I want to use a board to build my own button box.
  I wanted to make sure that Open Sesame can detect a 5Vdc on four different pins . It will be a 5Vdc pulse of about 50 milliseconds. (I will use it with a windows computer)

  This is the board:
  http://www.ebay.com/itm/Leonardo-Pro-Micro-ATmega32U4-8MHz-3-3V-Replace-ATmega328-Arduino-Pro-Mini-/131694495857?hash=item1ea99a8871:g:hdoAAOSwX~dWjOXq

  Thank you,

  Tali
• Jarik

  August 2016

  Hi Tali,

  I saw that there are ways to built you own USB button box.

  Where are you referring to?

  I think the big question is what firmware are you going to put into the board and does that support a button box protocol OpenSesame supports.

  Best,
  Jarik
• labovich

  August 2016

  Hi Jarik

  This is the firmware:

  http://www.ebay.com/itm/Leonardo-Pro-Micro-ATmega32U4-8MHz-3-3V-Replace-ATmega328-Arduino-Pro-Mini-/131694495857?hash=item1ea99a8871:g:hdoAAOSwX~dWjOXq

  Whether it will be supported by button box protocol is exactly my question (:

  Thanks!
  Tali
• Jarik

  August 2016

  Hi Tali,

  The firmware is the software that you put in the hardware board you found on eBay. This board will probably ship empty or at least not with firmware that can 'talk' to OpenSesame.

  In my opinion you have two options:

  • Either stick to the good old LPT printer port (not USB!) that can detect dc pulses on the pins and is supported by OpenSesame. Mostly used to send sync pulses from OpenSesame to EEG but can also be used as input. On a laptop this is a no-go but in a PC you could use a PCI Express Parallel port card. See this post for example.
  • Or you can try building @Sebastiaan his Boks (http://osdoc.cogsci.nl/2.8/boks/) but I don't know if the Boks plugin will work with OpenSesame 3. Search the forum for 'Boks' for more info.

  Best,
  Jarik
• sebastiaan

  August 2016

  Or you can try building @Sebastiaan his Boks (http://osdoc.cogsci.nl/2.8/boks/) but I don't know if the Boks plugin will work with OpenSesame 3. Search the forum for 'Boks' for more info.

  You could do that but the Boks requires that the Arduino and the buttons are set up in a particular way. Seeing how the Boks works could help you get started though, especially if you don't have a lot of experience. You could also take a look at StimSync:

  • http://www.mccauslandcenter.sc.edu/crnl/stimsync-0

  More generally, @labovich, I have the impression that you're misunderstanding the principle of building a button box with an Arduino. When you do this, you write the firmware, or 'sketch' in Arduino terminology. So it's up to you to write an Arduino sketch and a piece of Python code running in OpenSesame, in such a way that they communicate. Does that make sense?

  So this question:

  I wanted to make sure that Open Sesame can detect a 5Vdc on four different pins . It will be a 5Vdc pulse of about 50 milliseconds. (I will use it with a windows computer)

  Is not answerable or applicable--it depends on how you build the Arduino and write the software.

  Cheers,
  Sebastiaan

  
  
  Check out SigmundAI.eu for our OpenSesame AI assistant!
  
• labovich

  August 2016

  Thank you!
  It's been helpful (: